Official firmware update is V2.0.12 As of 10\25\2017
- Thread starter Jagerbomb52
- Start date
Using the Beta firmware does not void your warranty at all. Autel has said many times your warranty is valid.
I think you will be happy with the beta as many of us are.
Remember to update your batteries also.
It will fly like a different UAV so take your time getting used to how it flies.
Remember to update your batteries also.
It will fly like a different UAV so take your time getting used to how it flies.
yrless
Well-Known Member
I was able to get hold of another XSP loaded with V2 while my unit is out in Washington for repair......did another orbit test this hot and hazy morning with expo set to 7 (max), radius set to 150 feet and altitude at 120 feet AGL. The first orbit in the video is running at the default speed of approximately 9 mph......the second orbit is slowed down to about 4 mph so you can make a judgement call on speed vs. jerkiness.....personally I think both speeds look pretty darn good but please chime in if you think one is better than the other. I think the jerky-yaw orbit issue is basically solved with V2....just set expo to 7 before doing your orbit then set it back lower if you like for manual yaw control. Would love to know if anyone else has experimented 
EXP7B.mp4
EXP7B.mp4
It looks real smooth. I did some experimenting the other day and found mine to be jerky. I am right up to date on the beta firmware. I tried Exo 0.20 and then 0.70. If you looked at the center of my videos they were fine but if you were watching the left of right side it jerked real bad.
yrless
Well-Known Member
Just wondering what your orbit radius was set to when you ran the test....a tight radius requires constant yaw correction so I try to set mine way out like 150+ feet so the aircraft only has to make small corrections to stay fixed on the centroid. Just a thought.
I did a commercial shoot last week after updating to 2.0.8 and my orbit footage was as jerky as can be. I should have thought it through and allowed for the possibility that the perfect orbit performance could be degraded with the update. I was so delighted with the performance of 2.0.1. My orbit radius was about 300' and yaw expo was set to max, so it should have been smooth. I'm kicking myself a bit for trusting that the orbit performance wouldn't change for the worse. Oh well, I'm glad it's not just me and that my observations are supported by others' experience.
yrless
Well-Known Member
By all accounts, it's not possible. The genie is out of the bottle. I just hope they put out a better version soon. If it works for the most part in terms of smooth yaw, I will sit on that until the public release. Even then I will wait for reports. Wrote this while Agustine was writing his answer.
yrless
Well-Known Member
Steambc I'm just wondering why you had such poor orbit performance... If you go back to post #65 I included links to 2 orbit flights done with different expos settings in V2.0.8...EXP7 looks pretty stable to me (as compared to EXP3) but maybe I have loose standards 
Can you tell me how your flights compare to my vids?
Can you tell me how your flights compare to my vids?
upload it to youtube and post the link here. This forum does not allow video uploads.
Previously, I would fly the bird directly overhead of the POI, start the orbit "From Aircraft", and then once it flew to position and I adjusted the camera angle, it would point at the POI very accurately for the entire orbit. In this video, I had set the POI to the center of the building.
Now, if I do the same thing, the Point of Interest is always about 30 or 40 yards to the left of the starting point. I have calibrated the compass twice in my usual open field, no metal, dental fillings removed, and calibrated the TX.
Also removed camera from mount and slid it back and forth a few times for good contact.
Now, if I do the same thing, the Point of Interest is always about 30 or 40 yards to the left of the starting point. I have calibrated the compass twice in my usual open field, no metal, dental fillings removed,
and calibrated the TX.Also removed camera from mount and slid it back and forth a few times for good contact.
yrless
Well-Known Member
Yeah that's a lot jerkier than my test flight with v2.0.8/expo7.....in fact it looks exactly like the results I was getting in v1.1.3. Is it possible that one or more modules didn't actually update when you loaded 2.0.8? Do you think a re-load might be a possibility to fix this? Just thinking out loud here 
I think it's a long shot, but a good idea. I'll re-download and try the update again. Fingers crossed!
Thanks for taking an interest.
Thanks for taking an interest.
yrless
Well-Known Member
I think our interests are aligned
I'm going to open a new ticket with support to see if we can get on the payroll.
Similar threads
Latest threads
-
-
-
-
Autel 640t Enterprise Lite „OA (Obstacle avoidance) abnormal“ drone became not responsive.
- Started by LexusWorld
- Replies: 0
-