Welcome, Autel Pilots!
Join our free Autel drone community today!
Join Us

Recent content by jaja6009

  1. J

    RTK

    We all have to start somewhere. Good Luck, hopefully this gets you up and running.
  2. J

    RTK

    Do you have previous experiance with GNSS receivers? If so, it is very similar. The RTK module works like a terrestrial GNSS unit or a rover. When you signed up for the free RTK corrections, they gave you credentials to access the system. You must go to the RTK menu page in Autel Explorer...
  3. J

    RTK

    Are you sure you are receiving corrections? Do you have FLOAT or FIX?
  4. J

    RTK

    Most likely, you have RTK turned on and are not receiving corrections through NTRIP. If you live in a state with free RTK corrections you can use that. Or you can pay for a service such as Trimble, Point One or something similar. Point One most liekly has a free trial if you want to signup and...
  5. J

    New EVO 2 6k V.2 owner. Should I have gotten a V.3?

    There is nothing to deal with concerning RID on the V3. RID is built in and you pretty much do not have to worry about it. You power on, do your preflights and fly. V1/V2 will need an add-on module that is a pain in the butt since it needs to be attached, configured and charged (Constantly)...
  6. J

    DJI mateice 4t

    Is it during a 5 pattern mission where the first mission is nadir and the next 4 are oblique missions to get all sides? If so, then it is the Altitude Optimization running for the first, nadir images mission possibly. It could also be where your flight outline is not perfectly square and the...
  7. J

    DJI mateice 4t

    You will have better luck in the dedicated Matrice forum. https://matricepilots.com/ Here is my guess. Does this happen when you are on a mapping mission with nadir images only? If so, this is the altitude optimization. You can check this by opening the mission and seeing if Altitude...
  8. J

    Renew discussion--Cannot connect controller and Evo.

    This is what I am not getting. You are happily using the drone. You then do not fly it for months or in my case years. Why would it still not be paired when you go to fly it again? Our Evo did not fly from November of 2023 until I powered it on this week. It was paired and ready to go as if I...
  9. J

    Renew discussion--Cannot connect controller and Evo.

    I live in New Jersey, USA. Am I missing something with everyone else? How can a drone that previously was paired and worked and did not have any changes such as firmware, stop working all of a sudden?
  10. J

    Renew discussion--Cannot connect controller and Evo.

    The other thread on this had me worried. I tested my Evo and all is well. It works just as before. Here is my firmware screen.
  11. J

    Disgust and disappointment

    I tried again today, with a phone and the Explorer app. It worked fine. Is it because I am on an older firmware?
  12. J

    Disgust and disappointment

    I just tried my 2019 Evo. I did not use a phone with Autel Explorer as the phone was dead, but I will try with the phone tommorow. I have not flown it since August 2023. It was already linked to the controller on power up. I had connection and powered on the motors. I did not fly as I was...
  13. J

    Search light?

    https://advexure.com/products/autel-evo-max-speaker-and-spotlight?srsltid=AfmBOoqFS6iK1VOCeFAm94cMNmPY32hIIGqqZeRt9V3kBQJQmQqQy1Oo You can add a payload drop device also to give em a treat also...
  14. J

    Remote id module

    Sorry I tried typing the previous response on my phone. You cannot power the module using a USB C to USB C cable. You can install a small Remote ID module in the drone, but I would be very careful where you tap into for power. On drones you build you add accessories to a BEC (Battery...
  15. J

    Remote id module

    No.