Welcome, Autel Pilots!
Join our free Autel drone community today!
Join Us

Recent content by ovrszd

  1. ovrszd

    AUTEL EVO II FIRMWARE UPDATE: Constantly updated ( new V1 STABLE fw 2.7.35) - 28/02/2022 - (NEW V2 STABLE fw 2.3.8 - 19/04/2022)

    My glitches were a slight drift to the left after I stop stick movement. When I hand catch the drone hesitates a few seconds before shutting down the props. Otherwise, no problems.
  2. ovrszd

    AUTEL EVO II FIRMWARE UPDATE: Constantly updated ( new V1 STABLE fw 2.7.35) - 28/02/2022 - (NEW V2 STABLE fw 2.3.8 - 19/04/2022)

    Start the Drone first, then the controller and viewer. I never get that message done that way.
  3. ovrszd

    Auto land

    I'm not sure why your Drone decided to land. I was simply addressing how to stop it from doing so. I always hand catch mine. That means hovering at 6' or so. I guess in honesty I've not hovered at 3-4' to see what it would do.
  4. ovrszd

    Low Noise Propellers - appearance

    In my opinion, it's very unprofessional of Autel to ship the old props as a fill for the new prop design. Very, very unprofessional. One of two things. The shipping person doesn't care. Or, Autel management is getting rid of old props.
  5. ovrszd

    Auto land

    With my old XSP all I had to do was push the stick forward for Upward travel. Maybe on the E2P push the button on the controller with the red II symbol. That is used to cancel RTH, etc.
  6. ovrszd

    Will battery not charge unless i update it?

    We'll hope for some little glitch that you can work out. I have gotten two new batteries over the years that were bad in the box. Both were effortlessly replaced by Autel with email contact.
  7. ovrszd

    new 2.5.12 FW from today???

    In review it appears I got everything except the battery update. I'm still at V0.0.12.0
  8. ovrszd

    new 2.5.12 FW from today???

    Augustine, excuse my naive ignorance in describing what I've done but here goes. I checked the firmware versions in my E2P and wrote them all down. Then I did the latest firmware update. Here's my before/after data: Flight Control V0.0.1.97/V0.0.1.108 Camera V0.2.27.9/V0.2.29.24 Remote...
  9. ovrszd

    It's in the mail

    I started with an XSP, long landing legs. But I still hand caught it. I've flown the E2P 26 times. Never landed. Always hand caught. The camera is $800.....
  10. ovrszd

    verifying what I found searching

    For my simple needs, I have no use for a tablet. I fly using my Cell Phone and get along great. Actually can see everything very well. I used a tablet when flying my XSP. I guess I don't understand what you are trying to do. But that's normal for me. Most members here are far above my...
  11. ovrszd

    how to zoom?

    I did not know about the pinch thing. I'll try that next time. I always used the scroll bar method. thanks.
  12. ovrszd

    Excellent service experience

    I've always had good service from them as well.
  13. ovrszd

    MY EVO 2 Crash in the Sea.

    50% is better than 0%. I would decide if I want this Drone fixed or let it go and buy new Drone?
  14. ovrszd

    SD Card Write Slow error

    We've had horrible wind this year. I am Blessed to be Retired so I can pretty much fly on good days. :)
  15. ovrszd

    SD Card Write Slow error

    I do too. Thanks again. I've only flown once since getting the netac cards. Shot two videos of about 4 minutes each yesterday and didn't get a "slow" warning.